Home » How to Trial operation of three roll mill
How to Trial operation of three roll mill
Trial operation of three roll mill
The machine is working only under the material on the rollers.
Upon hearing unusual voice, please stop and check on time.
Please keep the machine no working, then Maintain and cleaning.
Preparation before operation
Ø Set the roller in loosen condition, turn the belt wheel by hand, clean all the dirt on roller, feeding hopper and outlet blade.
Adjust hydraulic pressure(Start oil pump motor before start main motor)
Ø Checking “mixing” “milling”process, the closed roller pressure is 3Mpa, have a fibe tuning device P2 pressure switch to 2-3 mpa.
Ø Check and adjust baffle pressure to 1.2Mpa
Ø Check and adjust the blade pressure around 1Mpa. Normally it’s 0.6Mpa. Or pressure can be decided as material characteristics.
Ø The roller pressure shall set at 5Mpa or based on material characteristics. The roller pressure adjustment range is 1~5.5Mpa;
Ø Set the rotating valve HV at “Loosen” position after finish adjusting pressure, run the hydraulic system several hours, operate the rotating valve several times.
Main motor must keep still during all above operation.
Trial operation
Ø put material over than the level of ultrasonic, then star working
Ø Turn on water valve, pour enough cooling water into roller before first time operation. Set the temperature controller at 0℃.Cooling water will enter roller cavity after turn on water valve. Set the temperature as requested in temperature controller after mill operation.
Ø press “stop main motor”, operate main motor, checking roller pressure, if possible, please check again.
Ø put into mixed material, press “milling” to “milling”position. Check the roller tightening at same step. Further adjustment is possible by adjusting valve if necessary.
Ø When the mill set at “Tighten” position, outlet hopper oil tank will tighten automatically.
Ø here are material exudation at the both sides of roller when roller set at “Mixing” and “Tightening”, it means there is gap between roller shaft shoulder and baffle. Please adjust roller axial position. Adjust the part 5 and 6 in chart 15, so as to make the middle roller and slow roller shaft shoulder face in same surface, that will make hopper baffle fit well with roller shaft shoulder.
Ø Set the ink discharge state when the mill working(see chart) State 3 is best. Ink discharge adjustment is comprehensive, it’s not only related with roller pressure, but also with temperature, outlet hopper position and blade edge.
Ø Ultrasound probes is installed over the place of putting material,checking the material level, if the material level is lower than set level, the machine will be stopped, but there is some material on roller, please open by hand, upon finished material then close machine by hand, and keep separate position of rollers in case of working without material.
Copyright Notice :
This article only represents the author’s point of view.
This article is published under the authorization of the author.
Source: Franli
This article address : How to Trial operation of three roll mill
Related Products
Turbine bead mill
FRANLI turbine bead mill is a kind of nano mill, which is mainly used in medicine, food industry, agrochemicals, cosmetics industry, papermaking, life sciences, microbiology, fillers, and other industries.
Dispersion Kneader
The dispersion kneader is suitable for the mastication of rubber and plastics, and the mixing of various rubber materials and plastics.
Vacuum Kneader
The vacuum kneader is an ideal equipment that is suitable for high-viscosity material, such as high-viscosity silicone rubber, sealant, gum, cellulose, etc. Also used widely in the Paint, ink, pigment, resin, battery, cosmetic, etc industries.
News
High Shear Mixers in Biopharmaceutical Applications
high shear mixers are highly versatile and can be used for a wide range of applications in biopharmaceutical manufacturing.
Operating Guide for Laboratory Reactors
Laboratory reactors play a crucial role in chemical research and development. Understanding the proper operating procedures is essential to ensure accurate results and maintain a safe working environment.
Glass Reactors and Selection of Stirring Blades
Glass reactors, also referred to as glass reaction vessels, are vessels made from high-quality borosilicate glass material.
High Shear Mixers in the Resin Industry
High shear mixers are essential equipment in the resin industry for achieving uniform dispersion of solids into liquid matrices, emulsifying oil-based components, and blending various additives to create resin formulations with desired characteristics.
High Speed Dispersers for Painting: Enhancing Efficiency and Quality in the Coating Industry
High-speed dispersers are powerful machines used in the paint and coating industry to disperse solid particles into liquid components effectively.
Ribbon Blender Mixer: The Right Choice for a High-Quality Blender
Ribbon blender mixers, also known as ribbon mixers or ribbon blenders, are horizontal mixing devices characterized by their unique ribbon-shaped agitators.