The use characteristics and skills of the Three roll mill

Home » The use characteristics and skills of the Three roll mill

The use characteristics and skills of the Three roll mill

Three roll mill is referred to as a triple roll mill. Three roll mill is the most efficient equipment for grinding and dispersing high viscosity materials. Three roll mills can be divided into laboratory three roll mills and production three roll mills. Both are mainly suitable for the production of paints, inks, pigments, plastics, and other slurries. Its working principle is to achieve the grinding effect through the surface extrusion of three horizontal rollers and friction at different speeds.

Working principle and design features

1. Three roll mill has three rollers installed on the iron frame, the center is straight. It can be installed horizontally or slightly inclined. The grinding effect is achieved by squeezing the surface of the three horizontal rollers and friction at different speeds. Steel drums can be hollow and can be cooled with water. Add material between the middle and rear rolls. Since the rotation directions of the three drums are different (the rotation speed increases sequentially from the back to the front), a good grinding effect is produced. After grinding, the material is scraped off by knives mounted in front of the front rollers.

2. When using the Three roll mill, check whether the position and locking of each part are normal. Add lubricating oil according to the marked point, turn on the power, adjust the front and rear handwheels, observe whether the roller system is normal, remove the dirt on the roller surface: wipe with soft paper or clean cotton yarn, loosen the baffle clamp, and adjust the front and rear rollers and the middle roller to 0.5 mm, then start the power supply and let it idle for 1-2 minutes.

3. Three roll mill is mainly used for various high-grade pastes, such as paints, inks, plastics, pigments, cosmetics, electronic pastes, solar silver pastes, aluminum pastes, glass solder pastes, etc. It is especially suitable for the grinding of products with high dispersion viscosity and high particle size required by the centrifugal casting of chilled gold cast iron rolls. The crystal phase is dense, the strength is high, the surface hardness is high, and the wear resistance is good.

The correct way to use the three roll mill

Rotation operation:

1. Open the Three roll mill to check:

(1) Check whether the roller surface of the Three roll mill is clean and whether there is any foreign matter between the rollers.

(2) Check whether the scraper is sharp

(3) Check whether each lubricating part is sufficiently lubricated.

2. Preparations before starting:

(1) Loosen the rollers in turn.
(2) Release the blanking knife.
(3) Slightly loosen the gear tip.
(4) Prepare the slurry tank (must be cleaned)
(5) Open the cooling water valve

3. Start:

(1) Press the Three roll mill start button to start.
(2) Appropriately press the tip of the gear and immediately load the material (paint)
(3) Rotate the handwheel, adjust the slow roller and the fast roller, move closer to the middle, observe that the roller surfaces are parallel, and adjust the tightness of the roller.

FRANLI Three roll mill has a leading position in wet grinding equipment. Currently, it has set up agencies in more than 20 countries in the world, and we have a complete and mature after-sales service to relieve users from worries before and after use. If you are still Finding a trusted partner you can contact us directly.

Copyright Notice :
This article only represents the author’s point of view.
This article is published under the authorization of the author.
Source: Franli

This article address : The use characteristics and skills of the Three roll mill

Related Products

all

Vacuum Double Planetary Mixer

A Vacuum double planetary mixer is an essential part of any industry to mixing particular material. A double planetary mixer contains two blades that help mix by revolving on their axis in the vessel.

Contact ➔

29 July

all

Dyno mills

Dyno mills are also widely used in inks. In the production of different types of ink, the structure of the dyno mill is also different. Probably follow the following rules, gravure ink: production generally uses pin or disc type dyno mill; rotary offset p

Contact ➔

28 July

all

3 Roll Mill: Manual, Hydraulic, Lab

3 Roll Mill is a great tool that is used to mix, refine, and disperse any material through three horizontal rolls situated opposite sides with different speeds.

Contact ➔

28 July

News

Laboratory Reactor: Guide to Stirring System

18 June

The laboratory reactor is composed of a pot body, a pot cover, an agitator, a jacket, a support and transmission device, a shaft seal device, etc.

Grinding Media for Bead Mill | Zirconia Beads & Zirconium Silicate Beads

17 June

Bead mills mainly use grinding balls as media, and use impact, extrusion, and friction to achieve the final grinding effect, which mainly depends on the size and hardness of the grinding beads, the filling rate of the grinding beads, and the collision frequency adjustment between the grinding beads and the particles.

Overview of Laboratory Reactor

28 May

Laboratory reactors, also known as lab reactors, are essential tools in scientific research, product development, and process optimization. These reactors provide a controlled environment for conducting chemical reactions, mixing, dispersing, and homogenizing processes.

The use characteristics and skills of the Three roll mill