Home » Bead mill for ink
Bead mill for ink
What kind of ink you are producing?Offset ink, gravure ink, printing ink, digital ink, letterpress ink, packaging inkjet, industrial inkjet, commercial inkjet?If the ink is discharged statically.
For inks, the wear on the wearing parts will be less, because the viscosity of the ink itself is relatively high, the oil is oily, and the zirconium bead wear is relatively small.
Nano Mill
Then our bead mill generally uses 0.2, 0.3mm, with static discharge, the screen is 0.3mm, if the beads are 0.2mm, the beads will run out, with 0.2mm beads, the processing accuracy of the bearing seat cannot be guaranteed. Bearings It is oily. In the process of operation, the coaxiality of the interbody is not so standard, so it is not acceptable to use 0.2-0.3mm beads. If the viscosity is low, use the meshless one, and the viscosity will be higher. Yes, it is necessary to bring a screen, the screen may use a gap of 0.05 or 0.1.
Cone bead mill
Disadvantages: In the cylinder bead mill, the linear velocity is not uniform. The linear velocity of the big head is the highest. When the cone rotates, the linear velocity of the big head is the highest, and the smallest head is the lowest. So when selecting the line speed, Whichever is the highest or the lowest? Line speed has a set value in the industry
If you take the big head as the standard, the small head linear velocity will be too low, which means that this part of the solvent space is equal to waste, and the efficiency is low; if the small head is the standard, the big head is low, the linear velocity will be very high, which will cause wear Intensified, it will also cause the temperature to be too high.
The FRANLI BEAD MILL is a machine for continuous superfine grinding and dispersing of solids in liquids. It works following the principle of agitator bead mills, where grinding media is accelerated in the grinding tank by an agitator shaft. The energy given to the media is passed onto the solid particles under collision and de-acceleration. Due to the tank being in a horizontal position, the special agitator gives an even activation of grinding media over the whole tank content.
The following advantages result from this:
• closer grain distribution;
• less strain on the grinding system;
Operation of bead mill
The Bead mill contains important information on how to 0 operate the machine safely properly and most efficiently.
Observing these instructions helps to avoid danger, to reduce repair costs and down-times, and to increase the reliability and life of the machine. The instruction manual is to be supplemented by the respective national rules and regulations for accident prevention and environmental protection.
The operating instructions must always be available wherever the bead mill is in use and must be read and applied by any person who carries out works on the machine. In addition to the operating instructions and the mandatory rules and regulations for accident prevention and environmental protection in the country and place of use of the machine, the generally recognized technical rules for safe and proper working must also be observed.
Therefore we kindly ask you for your understanding that changes in the design or of the models of our product range may arise, that are reasonable for the buyer.
Please be advised that no essential change in the function will take place.
No claims can be derived from the illustrations and descriptions of this operating manual.
These operating instructions of the bead mill are only applicable to the order confirmation number stated on the cover sheet. This number can also be found on the bead mill nameplate.
Welcome to check our factory and testing machines by your materials.
Copyright Notice :
This article only represents the author’s point of view.
This article is published under the authorization of the author.
Source: Franli
This article address : Bead mill for ink
Related Products
Three roll mill
Three roll mills are widely used in a variety of chemical industries, from medium to high viscosity productions. FRANLI machine can break open all kinds of pigment, UV ink, offset ink, decorative paints, and Lubricants, it also can catch the greatest fine
Dispersion Machine
This HSD-D Dispersion Machine with two shafts for mixing and dispersing materials to reach higher efficiency. This machine should be installed jacket tank with a cooling system. The dispersion machine has two shafts working temperature
Digital Control Three Roll Mill
The roller of the digital control three roll mill is made of zirconia ceramic material and equipped with a frequency conversion speed regulating device to meet the grinding needs of different materials.
News
Laboratory Reactor: Guide to Stirring System
The laboratory reactor is composed of a pot body, a pot cover, an agitator, a jacket, a support and transmission device, a shaft seal device, etc.
Grinding Media for Bead Mill | Zirconia Beads & Zirconium Silicate Beads
Bead mills mainly use grinding balls as media, and use impact, extrusion, and friction to achieve the final grinding effect, which mainly depends on the size and hardness of the grinding beads, the filling rate of the grinding beads, and the collision frequency adjustment between the grinding beads and the particles.
Overview of Laboratory Reactor
Laboratory reactors, also known as lab reactors, are essential tools in scientific research, product development, and process optimization. These reactors provide a controlled environment for conducting chemical reactions, mixing, dispersing, and homogenizing processes.
Bead mills | Manufacturing technology in various industries
Bead mills, also known as sand mills or grinding mills, are versatile machines widely used across various industries for the wet grinding and dispersion of solid particles in liquid media.
Ribbon Blender Mixer Equipment
A ribbon blender mixer, also known as a ribbon mixer or horizontal ribbon blender, is a powerful industrial machine designed for thorough and efficient blending of various materials.
What is A Stainless Steel Reactor?
Stainless steel reactors are essential equipment in various industries, including chemical, pharmaceutical, biotechnology, and food processing.