The use process of the three roll mill
Under normal circumstances, the material of the roller of the three roll mill is the centrifugal casting of chilled cast iron, and the surface hardness is above HS70°; the diameter of the roller is high-precision grinding, which is precise and fine, and the grinding fineness of the material can reach 15um. Therefore, it is possible to produce uniform and fine high-quality products. SM405, S260 type.
Three roll mills are used for mass production, and models S150 and S65 are used for small batches or laboratory use.
1. Preparation of the three roll mill:
① Check whether the position and locking of each component are normal, inject lubricating oil according to the point shown in the figure and turn on the power
②Adjust the front, rear, left, and right handwheels to observe whether the roller linkage is normal
③Remove the dirt on the roller surface: wipe with soft paper or clean cotton yarn, release the knob of the baffle plate
④ Adjust the gap between the front and rear rollers and the middle roller to 0.5 mm and then start the power supply to idle for 1–2 minutes.
2. Working rules of the three roll mill:
①After starting the operation, adjust the gap between the middle and rear rolls to 0.3 mm, press the baffle plate, add the slurry appropriately, visually inspect the coloring depth, fine-tune the rear rollers so that the coloring is evenly distributed over the rollers, and then lock the fixing nut.
②Adjust the handwheel of the front roller with both hands at the same time, so that the front roller slowly touches the middle roller and the surface of the front roller is evenly colored, then lock the fixing nut, and then adjust the angle of the material plate so that it is properly pressed on the roller surface, and the slurry can be uniform. discharge. Check the uniformity of the discharge and the particle size of the finished product, and continue to fine-tune the front and rear rollers until the particle size of the finished product reaches the predetermined requirements. The scraper should be returned in time before and after.
3. After the work of the three roll mill stops:
Remove the paint and clean it in time, wipe the roller and related parts, loosen the scraper and baffle, apply a small amount of oil, and then cover with wax paper for protection.
4. Precautions for three roll mill:
① The surface of the roll is strictly prohibited from bumping and scratching, and it is strictly forbidden for all kinds of metal objects and hard impurities to enter the running roll.
②The working temperature range of the roll: ordinary type: -5°C~100°C, heating type: 20C~220°C
③Roll and roller in normal working time: Gap range: (Reference) Middle and rear roller gap: 0.02~0.25mm, Middle and front roller gap: 0.01~0.25mm.
④ The peak angle of the baffle is strictly prohibited from being damaged, and the contact pressure with the roll surface should be appropriate during adjustment. There are three rollers mounted on an iron frame. The center is in a straight line. Can be installed horizontally, or slightly inclined. The grinding effect is achieved by the mutual extrusion of the surfaces of the three horizontal rollers and friction at different speeds. The steel drum can be hollow and cooled by water. The material is added between the middle roll and the rear roll. Because the rotation directions of the three drums are different (the rotation speed increases sequentially from the back to the front), a good grinding effect is produced. After the material is ground, it is scraped off by a scraper installed in front of the front roller.
Copyright Notice :
This article only represents the author’s point of view.
This article is published under the authorization of the author.
Source: Franli
This article address : The use process of the three roll mill
Related Products
Horizontal Bead Mill
Horizontal Bead Mill is used for the grinding of a solid-liquid two-phase system. In the grinding process, the material is pumped into the Horizontal Bead Mill, and the rotating grinding disc transfers energy to the beads. The beads impact the material an
Z Blade Mixer
The Z blade mixer is made for extensive mixing, kneading, and stabilizing strong and high viscous materials, such as bubble gum bases, bread, caramel mass, body wash platform, and glue.
Inline Emulsifier
The inline emulsifier is composed of three sets of stators (two layers, four layers, and six layers) in the working cavity, which has higher processing accuracy, large processing capacity, and wide processing viscosity range.
News
Ribbon Blender Mixer Equipment
A ribbon blender mixer, also known as a ribbon mixer or horizontal ribbon blender, is a powerful industrial machine designed for thorough and efficient blending of various materials.
What is A Stainless Steel Reactor？
Stainless steel reactors are essential equipment in various industries, including chemical, pharmaceutical, biotechnology, and food processing.
Inline Static Mixers: A Comprehensive Product Overview
Inline static mixers are the best devices that provide efficient and cost-effective mixing solutions for various industrial applications. These motionless mixers are designed to blend fluids within a pipeline without the need for moving parts or external power sources.
Glass Reactor & Chemical Equipment
Glass reactors are essential equipment widely used in the chemical, pharmaceutical, and biotechnology industries. They come in various types, suitable for different applications.
High Speed Dispersers: A Powerful Tool
At the heart of a high-speed disperser lies a robust shaft with a specially designed blade or rotor attached to its end. As the shaft rotates at high speeds, the blade generates powerful shear forces that tear apart agglomerates and disperse particles, ensuring a homogeneous and stable mixture.
High Shear Mixers in Biopharmaceutical Applications
high shear mixers are highly versatile and can be used for a wide range of applications in biopharmaceutical manufacturing.
